Orders shipped Monday-Friday from Arcadia, California.

SpeedyBee F405 Wing APP Flight Controller for iNav, Ardupilot

Your Price: $39.99
Out of Stock.
Part Number:SB-F405WING-APP

Choose Options

Accessories
GPS Receiver: Matek M10Q GNSS & Compass (+$40.99)
Airspeed Sensor: Matek ASPD-4525 (+$49.99)
SpeedyBee's F405 Wing APP Flight Controller is a revolution in low-cost, full-featured flight controllers for iNav and Ardupilot!


A GPS receiver is required for basic navigation functionality and to display positional data.  An airspeed sensor is also a great addition to fixed-wing flight controllers, as it gives the controller a deeper understanding of how the aircraft is moving through the air.  Options for both of these accessories are available above.

SpeedyBee F405 WING FC board Specifications:
MCU: STM32F405,168MHz,1MB Flash
IMU(Gyro&Accelerometer): ICM-42688-P
Barometer: SPL006-001
OSD Chip: AT7456E
Blackbox: MicroSD Card Slot
UART: 6 sets(USART1, USART2, USART3, UART4, UART5, UART6 (Dedicated for Wireless board Telemetry connection))

I2C: 1x Used for magnetometer, digital airspeed sensor
ADC: 4x (VBAT, Current, RSSI, Analog AirSpeed)
PWM: 12x (11+1“LED”pad)
ELRS/CRSF receiver: Supported, connected to UART1
SBUS: Built in inverter for SBUS input (UART2-RX)
LED: 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red) 1x RGB
RSSI: Supported, named as RS .

Supported FC Firmware: 
INAV--SpeedyBeeF405WING (default)
ArduPilot--SpeedyBeeF405WING

Weight: 8.9g

 
SpeedyBee F405 WING PDB board Specifications:
Input voltage range: 7~36V (2~6S LiPo)
Battery Voltage Sensor: Connect to FC board VBAT, 1K:10K (Scale 1100 in iNav, BATT_VOLT_MULT 11.0 in ArduPilot)
Battery Current Sensor: 90A continuous, 215A peak Connect to FC board Current (Scale 195 in iNav, 50 A/V in ArduPilot)
TVS Protective diode: Yes

FC BEC output: Output 5.2V +/- 0.1V DC Continuous current 2.4 Amps, 3A Peak Designed for FC, Receiver, GPS module, AirSpeed module, Telemetry module, WS2812 LED_Strip

VTX BEC output: Output 9V +/- 0.1V DC Continuous current 1.8 Amps, 2.3A Peak Voltage adjustable, 9V Default, 12V or 5V via jumper Designed for Analog Video Transmitter,Digital Video Transmitter, Camera.

Servo BEC output: Output 4.9V +/- 0.1V DC Continuous current 4.5 Amps, 5.5A Peak Voltage adjustable, 4.9V Default, 6V or 7.2V via jumper Designed for Servos.
Weight: 11.4g
 
SpeedyBee F405 WING Wireless board Specifications:
Wireless Configuration (long press BOOT button for 6 seconds to switch modes): BLE mode, connect to Speedybee APP

Wi-Fi mode, connect to QGroundControl APP, Speedybee APP, MissionPlanner, etc.
Classic Bluetooth SPP mode, connect to QGroundControl APP, MissionPlanner

LED strip controller (short press BOOT button to switch effects, long press 2 seconds to switch modes): 4x WS2812 LED strip connectors, adjustable colors and flashing modes

Max 5.2V 1.3A, supports around 70pcs 5050 WS2812 LED beads
On-board battery level indicator: 4x RGB indicator LED for battery level display by number of lights

Weight: 4.2g


Recently Viewed Items